Crown XLS2500

• Stereo, 2 ohms (per ch.): 1550W
  
• Stereo, 4 ohms (per ch.): 775W
  
• Stereo, 8 ohms (per ch.): 440W
  
• Bridge-Mono, 8 ohms: 1550W
  
• Bridge-Mono, 4 ohms: 2400W
  
  
• XLS High Performance, Lightweight Class D amp weighs less than 11 lbs.
  
• Integrated PureBand™ Crossover System for better performance and control
  
• Peakx™ Limiters provide maximum output while protecting your speakers
  
• XLR, 1/4", RCA inputs provide outstanding flexibility
  
• Efficient forced-air fans prevent excessive thermal buildup
  
• Electronically balanced XLR inputs; touchproof binding post and Speakon® outputs
  
• Precision detented level controls, power switch, power LED, and six LEDs which indicate signal, clip and fault for each channel
  
• Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications
  
  
• Sensitivity (for full rated power at 4 ohms): 1.4 Vrms
  
• Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB
  
• Signal-to-Noise Ratio, Rated as dBr to full rated 8Ω power output (A-Weighted): > 103 dB
  
• Damping Factor (8 ohm): 10 Hz to 400 Hz: > 200
  
• Crosstalk (below rated 8Ω power): At 1kHz: > 85dB, At 20kHz: >55dB
  
• Input Impedance (nominal): 20 k ohms balanced, 10 k ohms unbalanced
  
• Load Impedance: 2 to 8 ohms per channel in Stereo, 4 to 8 ohms in Bridge Mono
  
• AC Line Voltage and Frequency Configurations Available (± 10%): 120 VAC 60 Hz, 100 VAC 50/60 Hz, 220 and 240 VAC 50 Hz
  
• Ventilation: Flow-through ventilation from front to back
  
• Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation
  
• Air Volume Requirements (per minute per unit): 80.15 ft³ (2.27 m³)
  
  Integrated Processing
  
• PureBand™ Crossover System
  
• Crossover Filter: Linkwitz-Riley 24dB per Octave
  
• Crossover Frequency Range: 50 HZ - 3 kHz
  
• Crossover Mode: Crossover (CH1=LPF, CH2=HPF), LowPass (both channels LPF), HighPass (both channels HPF), Bridge (LPF or HPF)
  
• Peakx™ limiters: Channel independent clip limiter designed to provide maximum output while protecting your loudspeakers
  
  Input/Output
  
• Input Connectors: XLR (one per channel), 1/4-Inch (one per channel), and RCA (one per channel). 1/4-Inch connectors can be used as loop-thrus to distribute signal to additional amplifiers.
  
• Output Connectors: Two 4-Pole Speakon® Output Connectors accept 2-pole or 4-pole Speakon® connectors. The top Speakon connector is wired for both channels so it can be used for bridgemono wiring or for stereo wiring of two speakers to a single Speakon connector.
  
• One pair of back-panel binding posts per channel; accepts banana plugs or bare wire. (European models do not accept banana plugs.)
  
  
• Construction: 10.35-Inch (26.29cm) depth
  
• Dimensions: EIA Standard 19-inch (48.3-cm) rack mount width, (EIA RS-310-B), 3.5-inch (8.9-cm) height, 10.7-inch (27.2-cm) depth
  
• Net Weight: 10.75 lb (4.9kg)